View B101EW02V0_5670650.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 ( ) preliminary specifications ( v ) final specifications module 10.1? sd+ 16:9 color tft-lcd model name b101ew02 v0 note ( ) led backlight with driving circuit design customer date all 4/21/2009 checked & approved by date note: this specification is subject to change witho ut notice. approved by date 4/21/2009 prepared by 4/21/2009 nbbu marketing division / au optronics corporation www..net
2 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 contents 1. handling precautions.............................. ................................................... ....................... 4 2. general description .............................. ................................................... ......................... 5 2.1 general specification.......................... ................................................... ................................................... ...... 5 2.2 optical characteristics ........................ ................................................... ................................................... ..... 6 3. functional block diagram ................................................... ............................................ 11 4. absolute maximum ratings.......................... ................................................... ................ 12 4.1 absolute ratings of tft lcd module............. ................................................... ......................................... 12 4.2 absolute ratings of environment................ ................................................... ............................................. 12 5. electrical characteristics ...................... ................................................... ........................ 13 5.1 tft lcd module................................. ................................................... ................................................... ..... 13 5.2 backlight unit ................................. ................................................... ................................................... ......... 15 6. signal characteristic ............................ ................................................... ........................ 16 6.1 pixel format image............................. ................................................... ................................................... ..... 16 6.2 the input data format.......................... ................................................... ................................................... .... 17 6.3 signal description/pin assignment .............. ................................................... ............................................ 18 6.4 interface timing............................... ................................................... ................................................... ........ 20 6.5 power sequence................................. ................................................... ................................................... ..... 21 6.5.1 panel power sequence ......................... ................................................... .................................................. 2 1 7. panel reliability test ........................... ................................................... ........................ 22 7.1 vibration test ................................. ................................................... ................................................... .......... 22 7.2 shock test..................................... ................................................... ................................................... ........... 22 7.3 reliability test ............................... ................................................... ................................................... .......... 22 8. mechanical characteristics...................... ................................................... ..................... 23 8.1 lcm outline dimension.......................... ................................................... ................................................... 23 9. shipping and package................................. ................................................... ................. 25 9.1 shipping label format.......................... ................................................... ................................................... .. 25 9.2 carton package................................. ................................................... ................................................... ....... 26 9.3 shipping package of palletizing sequence ....... ................................................... ....................................... 26 10. appendix: edid description .......................... ................................................... ............. 27 www..net
3 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 record of revision version and date page old description new description remark 0.1 2008/10/29 all first edition for customer 0.2 2009/1/14 5 power consumption (typ) power consu mption (max) 0.2 2009/1/14 5,6 white luminance 180nit typ. white luminance 200nit typ. 0.3 2009/1/20 32 edid tbd update edid 0.4 2009/2/23 6 update response time and color / chromaticity coodinates 0.4 2009/2/23 30 add hw code control table 0.4 2009/2/23 28~29 update 2d drawing (change connector position) 1.0 2009/4/21 final edition for customer www..net
4 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 1. handling precautions 1) since front polarizer is easily damaged, pay att ention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact wi th water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with a bsorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break o r crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) at the insertion or removal of the signal interf ace connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an en closure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration th at no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) small amount of materials having no flammabilit y grade is used in the lcd module. the lcd module should be supplied by power complied wit h requirements of limited power source (iec60950 or ul1950), or be applied exemptio n. 13) disconnecting power supply before handling lcd modules, it can prevent electric shock, do not touch the electrode parts, cables, connectors a nd led circuit part of tft module that a led light bar build in as a light source of back light unit. it can prevent electrostatic breakdown. www..net
5 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 2. general description b101ew02 v0 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and led backlight system. the scree n format is intended to support the 1280(h) x 720(v) screen and 262k colors (rgb 6-bits data driv er) with led backlight driving circuit. all input signals are lvds interface compatible. b101ew02 v0 is designed for a display unit of noteb ook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 255.54(w?) active area [mm] 222.72(h) x 125.28(v) pixels h x v 1280x3(rgb) x 720 pixel pitch [mm] 0.1740 (h) x 0.1740 (v) pixel arrangement r.g.b. vertical stripe display mode normally white white luminance note: i led is led current [cd/m 2 ] 200 typ (note1) luminance uniformity (5p) 1.25 max contrast ratio 500 typ response time [ms] 16 typ nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] typ max note 2.7w 2.9w type i , v in =12v 3.1w 3.3w type i , v in =5v weight [grams] 200 max. physical size [mm] l w t max 235.5 143.5 5.2 typical 235 143.2 - min 234.5 142.9 - electrical interface 1 channel lvds www..net
6 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 glass thickness [mm] 0.5 surface treatment glare support color 262k colors ( rgb 6-bit ) temperature range operating storage (non-operating) [ o c] [ o c] 0 to +50 -20 to +60 rohs compliance rohs compliance 2.2 optical characteristics the optical characteristics are measured under stab le conditions at 25 (room temperature) : item symbol conditions min. typ. max. unit note white luminance i led =20ma 5 points average 170 200 - cd/m 2 1, 4, 5 r l horizontal (right) cr = 10 (left) 40 40 45 45 - - degree viewing angle h l vertical (upper) cr = 10 (lower) 10 30 15 35 - - 4, 9 luminance uniformity 5p 5 points - - 1.25 1, 3, 4 luminance uniformity 13p 13 points - - 1.60 2, 3, 4 contrast ratio cr 400 500 - 4, 6 cross talk % 4 4, 7 t r rising - 12 - t f falling - 4 - response time t rt rising + falling - 16 - msec 4, 8 rx 0.549 0.579 0.609 red ry 0.318 0.348 0.378 gx 0.306 0.336 0.366 green gy 0.524 0.554 0.584 bx 0.126 0.156 0.186 blue by 0.105 0.135 0.165 wx 0.283 0.313 0.343 color / chromaticity coodinates white wy 0.299 0.329 0.359 ntsc % cie 1931 - 45 - 4 www..net
7 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 note 1 : 5 points position (ref: active area) 1 2 3 4 5 h /4 h /4 h /4 h /4 h w w /4 w /4 w /4 w /4 note 2 : 13 points position (ref: active area) w /4 w w /4 h h /4 h /4 h /4 h /4 7 9 1 0 w /4 1 8 w /4 1 0 1 0 1 0 1 0 2 3 1 3 1 2 4 5 6 1 1 note 3 : the luminance uniformity of 5 or13 points is defi ned by dividing the maximum luminance values by the minimum test point luminance w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum brightness of five points w5 = minim um brightness of five points www..net
8 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 note 4 : measurement method the lcd module should be stabilized at given temper ature for 30 minutes to avoid abrupt temperature ch ange during measuring. in order to stabilize the luminan ce, the measurement should be executed after lighti ng backlight for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen. note 5 definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the poin t x at figure in note (1). note 6 definition of contrast ratio: contrast ratio is calculated with the following for mula. center of the screen tft - lcd module 50 cm photo detector lcd panel field=2 contrast ratio (cr)= brightnes s on the ?white? state brightness on the ?black? state www..net
9 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 note 7 definition of cross talk (ct) ct = | y b ? y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) note 8 : definition of response time: the output signals of bm-7 or equivalent are measur ed when the input signals are changed from ?black? to ?white? (falling time) and from ?white? to ?black? (rising time), respectively. the response time inte rval between the 10% and 90% of amplitudes. refer to figure as below . s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% www..net
10 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 note 9 . definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal an d 180 vertical range (off-normal viewing angles). th e 180 viewing angle range is broken down as follow s; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measureme nt direction is typically perpendicular to the display surface with the scree n rotated about its center to develop the desired measurement viewing angle. www..net
11 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 3. functional block diagram the following diagram shows the functional block of the 10.1 inches wide color tft/lcd 40 pin (one ch/connector module: tft lcd 1280x(3) x720 pixels tft lcd 1280x(3) x720 pixels www..net
12 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 4. absolute maximum ratings an absolute maximum rating of the module is as foll owing: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive voltage vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 4 operation humidity hop 5 95 [%rh] note 4 storage temperature tst -20 +60 [ o c] note 4 storage humidity hst 5 95 [%rh] note 4 note 1: at ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: led specification refer to section 5.2 note 4: for quality performance, please refer to au o iis (incoming inspection standard) . twb=39c operating range storage range www..net
13 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble parameter min typ max unit s note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power - 0.7 0.8 [watt ] note 1/2 idd idd current - - 250 [ma] note 1/2 irush inrush current - - 1500 [ma] note 3 vddrp allowable logic/lcd drive ripple voltage - - 100 [mv] p-p note 1 : maximum measurement condition black pattern note 2 typical measurement condition: mosaic pattern note 3 measure condition +5.0v +12.0v vcc r1 47k r2 1k vr1 47k sw1 sw mag-spst 1 2 f1 q3 ao6402 g d2 s d1 d5 d6 c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v (high to low) control signal (lcd module input) 90% 10% vin rising time 0v 3.3v 470us www..net
14 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. it is recommended to refer the specifications of sn 75lvds82dgg (texas instruments) in detail. signal electrical characteristics are as follows; parameter condition min max unit v th differential input high threshold (vcm=+1.2v) 100 [mv] v tl differential input low threshold (vcm=+1.2v) -100 - [mv] v id differential input voltage 100 600 [mv] v cm differential input common mode voltage 1.125 1.375 [v] note: lvds signal waveform www..net
15 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 5.2 backlight unit 5.2.1 led characteristics parameter symbol min typ max units condition - 2.0 2.1 [watt] (ta=25 ), note 1 type i , v in =12v backlight power consumption pled - 2.4 2.5 [watt] (ta=25 ), note 1 type ii , v in =5v led life-time n/a 12,000 - - hour (ta=25 ), note 2 i f =20 ma note 1: calculator value for reference p led = v f (normal distribution) * i f (normal distribution) / efficiency note 2: the led life-time define as the estimated time to 50% degradation of initial luminous note 3: this panel will support lower duty ratio at pwm co nditional frequency. the pwm frequency constrain between 100 hz to 300 hz and a same typical 200hz. the duty ratio support from 5% to 100%. 5.2.2 backlight input signal characteristics parameter symbol min typ max units remark 6.0 12.0 21.0 [volt] type i, note 1 led power supply vled 4.5 5 5.5 [volt] type ii, note 1 led enable input high level 2.5 - 5.5 [volt] led enable input low level vled_en - - 0.8 [volt] pwm logic input high level 2.5 - 5.5 [volt] pwm logic input low level vpwm_en - - 0.8 [volt] pwm input frequency fpwm 100 - 1k hz pwm duty ratio duty 5 -- 100 % pwm frequency <500 hz pwm duty ratio duty 15 -- 100 % pwm frequency R 500 hz note 1: type i and ii is an independent of design parameter. it should b e separated from system design. www..net
16 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the inpu t signals and lcd pixel format. 1 1280 1st line 720th line 1 1280 1st line 720th line www..net
17 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 6.2 the input data format signal name description r5 r4 r3 r2 r1 r0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. g5 g4 g3 g2 g1 g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. b5 b4 b3 b2 b1 b0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the typical frequency is 54.2mhz.the signal is used to strobe the pixel data and de signals. all pixel data shall be valid at the falling edge when the de signal is high. de display timing this signal is strobed at the fal ling edge of rxclkin. when the signal is high, the pixel data shall be valid to be displayed. vs vertical sync the signal is synchronized to rxcl kin . hs horizontal sync the signal is synchronized to rx clkin . note: output signals from any system shall be low o r high-impedance state when vdd is off. www..net
18 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 6.3 signal description/pin assignment pin signal description 1 nc no connection (reserve) 2 avdd powersupply,3.3v(typical) 3 avdd powersupply,3.3v(typical) 4 dvdd ddc 3.3vpower 5 nc no connection (reserve) 6 scl ddcclock 7 sda ddcdata 8 rin0- -lvdsdifferential data input(r0-r5,g0) 9 rin0+ +lvdsdifferential data input(r0-r5,g0) 10 gnd ground 11 rin1- -lvdsdifferential data input(g1-g5,b0-b1) 12 rin1+ +lvdsdifferential data input(g1-g5,b0-b1) 13 gnd ground 14 rin2- -lvdsdifferential data input(b2-b5,hs,vs,de ) 15 rin2+ +lvdsdifferential data input(b2-b5,hs,vs,de) 16 gnd ground 17 clkin- -lvdsdifferential clock input 18 clkin+ +lvdsdifferential clock input 19 gnd ground?shield 20 nc no connection (reserve) 21 nc no connection (reserve) 22 gnd ground?shield 23 nc no connection (reserve) 24 nc no connection (reserve) 25 gnd ground?shield 26 nc no connection (reserve) 27 nc no connection (reserve) 28 gnd ground?shield 29 nc no connection (reserve) 30 nc no connection (reserve) 31 vled_gnd led ground 32 vled_gnd led ground 33 vled_gnd led ground 34 nc no connection (reserve) 35 pwm system pwm signal input 36 led_en led enable pin(+3.3v input) 37 nc no connection (reserve) 38 vled led power supply 5v~21v 39 vled led power supply 5v~21v 40 vled led power supply 5v~21v lvds is a differential signal technology for lcd in terface and high speed data transfer device. www..net
19 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 note1 : start from right side note1: input signals shall be low or high-impedance state when vdd is off. pin 40 pin 1 nc vled www..net
20 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1280 x 720 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate - 60 hz clock frequency 1/ t clock 57.2 62.2 90 mhz period t v 728 736 1023 active t vd 720 720 720 vertical section blanking t vb 8 16 303 t line period t h 1310 1408 2047 active t hd 1280 1280 1280 horizontal section blanking t hb 30 128 767 t clock note : de mode only 6.4.2 timing diagram dotclk de t h t hb t hd de t v t vb t vd input timing definition ( de mode) t clock input data pixel 1 pixel 2 pixel 3 pixel n-1 pixel n invaild data invaild data pixel 1 www..net
21 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 6.5 power sequence 6.5.1 panel power sequence vdd power and led on/off sequence is as follows. in terface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. . power sequence timing value parameter min.(ms) typ.(ms) max.(ms) condition t1 0.5 - 10 t2 0 - 50 t3 200 - - t4 0.5 - 10 t5 10 - - t6 10 - - t7 0 - - 10 200 v led =6~21v (type i) t8 10 - - v led =5v (type ii) t9 0 - 10 t10 200 - - t11 0.5 - 50 t12 0 - 10 t13 400 - - www..net
22 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 7. panel reliability test 7.1 vibration test test spec: test method: non-operation acceleration: 1.5 g frequency: 10 - 500hz random sweep: 30 minutes each axis (x, y, z) 7.2 shock test test spec: test method: non-operation acceleration: 220 g , half sine wave active time: 2 ms pulse: x,y,z .one time for each side 7.3 reliability test items required condition note temperature humidity bias ta= 40 , 90%rh, 300h high temperature operation ta= 50 , dry, 300h low temperature operation ta= 0 , 300h high temperature storage ta= 60 , 35%rh, 300h low temperature storage ta= -20 , 50%rh, 250h thermal shock test ta=-20 to 60 , duration at 30 min, 100 cycles esd contact : 8 kv air : 15 kv note 1 note1: according to en 61000-4-2 , esd class b: some perf ormance degradation allowed. no data lost . self-recoverable. no hardware failures. remark: mtbf (excluding the led): 30,000 hours with a conf idence level 90%. www..net
23 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 8. mechanical characteristics 8.1 lcm outline dimension www..net
24 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 www..net
25 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 9. shipping and package 9.1 shipping label format * h/w code control table : ic combination control code h/w source radium gate radium 1axxg 1a www..net
26 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 9.2 carton package 9.3 shipping package of palletizing sequence www..net
27 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 10. appendix: edid description b101ew02 v0 edid code address function value value value hex hex bin dec 00 header 00 00000000 0 01 ff 11111111 255 02 ff 11111111 255 03 ff 11111111 255 04 ff 11111111 255 05 ff 11111111 255 06 ff 11111111 255 07 00 00000000 0 08 eisa manuf. code lsb 06 00000110 6 09 compressed ascii af 10101111 175 0a product code d5 11010101 213 0b hex, lsb first 20 00100000 32 0c 32-bit ser # 00 00000000 0 0d 00 00000000 0 0e 00 00000000 0 0f 00 00000000 0 10 week of manufacture 01 00000001 1 11 year of manufacture 13 00010011 19 12 edid structure ver. 01 00000001 1 13 edid revision # 03 00000011 3 14 video input def. (digital i/p, non-tmds, crgb) 80 10000000 128 15 max h image size (rounded to cm) 16 00010110 22 16 max v image size (rounded to cm) 0d 00001101 13 17 display gamma (=(gamma*100)-100) 78 01111000 120 18 feature support (no dpms, active off, rgb, tmg blk#1) 0a 00001010 10 19 red/green low bits (lower 2:2:2:2 bits) 43 01000011 67 1a blue/white low bits (lower 2:2:2:2 bits) 25 00100101 37 1b red x (upper 8 bits) 94 10010100 148 1c red y/ higher 8 bits 59 01011001 89 1d green x 56 01010110 86 1e green y 8d 10001101 141 1f blue x 28 00101000 40 20 blue y 22 00100010 34 21 white x 50 01010000 80 22 white y 54 01010100 84 23 established timing 1 00 00000000 0 24 established timing 2 00 00000000 0 25 established timing 3 00 00000000 0 26 standard timing #1 01 00000001 1 27 01 00000001 1 28 standard timing #2 01 00000001 1 www..net
28 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 29 01 00000001 1 2a standard timing #3 01 00000001 1 2b 01 00000001 1 2c standard timing #4 01 00000001 1 2d 01 00000001 1 2e standard timing #5 01 00000001 1 2f 01 00000001 1 30 standard timing #6 01 00000001 1 31 01 00000001 1 32 standard timing #7 01 00000001 1 33 01 00000001 1 34 standard timing #8 01 00000001 1 35 01 00000001 1 36 pixel clock/10000 lsb 06 00000110 6 37 pixel clock/10000 usb 18 00011000 24 38 horz active lower 8bits 00 00000000 0 39 horz blanking lower 8bits 70 01110000 112 3a horzact:horzblnk upper 4:4 bits 50 01010000 80 3b vertical active lower 8bits d0 11010000 208 3c vertical blanking lower 8bits 10 00010000 16 3d vert act : vertical blanking (upper 4:4 bit) 20 00100000 32 3e horzsync. offset 30 00110000 48 3f horzsync.width 20 00100000 32 40 vertsync.offset : vertsync.width 36 00110110 54 41 horz&vert sync offset/width upper 2bits 00 00000000 0 42 horizontal image size lower 8bits de 11011110 222 43 vertical image size lower 8bits 7d 01111101 125 44 horizontal & vertical image size (upper 4:4 bits) 00 00000000 0 45 horizontal border (zero for internal lcd) 00 00000000 0 46 vertical border (zero for internal lcd) 00 00000000 0 47 signal (non-intr, norm, no stero, sep sync, neg pol ) 18 00011000 24 48 detailed timing/monitor 00 00000000 0 49 descriptor #2 00 00000000 0 4a 00 00000000 0 4b 0f 00001111 15 4c 00 00000000 0 4d 00 00000000 0 4e 00 00000000 0 4f 00 00000000 0 50 00 00000000 0 51 00 00000000 0 52 00 00000000 0 53 00 00000000 0 54 00 00000000 0 55 00 00000000 0 56 00 00000000 0 57 00 00000000 0 www..net
29 of 29 au optronics corporation product specification b101ew02 v0 document version : 1.0 58 00 00000000 0 59 20 00100000 32 5a detailed timing/monitor 00 00000000 0 5b descriptor #3 00 00000000 0 5c 00 00000000 0 5d fe 11111110 254 5e 00 00000000 0 5f manufacture 41 01000001 65 60 manufacture 55 01010101 85 61 manufacture 4f 01001111 79 62 0a 00001010 10 63 20 00100000 32 64 20 00100000 32 65 20 00100000 32 66 20 00100000 32 67 20 00100000 32 68 20 00100000 32 69 20 00100000 32 6a 20 00100000 32 6b 20 00100000 32 6c detailed timing/monitor 00 00000000 0 6d descriptor #4 00 00000000 0 6e 00 00000000 0 6f fe 11111110 254 70 00 00000000 0 71 manufacture p/n 42 01000010 66 72 manufacture p/n 31 00110001 49 73 manufacture p/n 30 00110000 48 74 manufacture p/n 31 00110001 49 75 manufacture p/n 45 01000101 69 76 manufacture p/n 57 01010111 87 77 manufacture p/n 30 00110000 48 78 manufacture p/n 32 00110010 50 79 manufacture p/n 20 00100000 32 7a manufacture p/n 56 01010110 86 7b manufacture p/n 30 00110000 48 7c 20 00100000 32 7d 0a 00001010 10 7e extension flag 00 00000000 0 7f checksum 36 00110110 54 www..net

▲Up To Search▲

Price & Availability of B101EW02V0

	To Download B101EW02V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .